Waukesha
Cherry-Burrell Products: Fittings
"S" Line BPE Fittings
Specifications
AWF/BPE Fittings Specifications
"S" Line
BPE Fittings Specifications
 |
Description: S-Line
Fittings which comply with ASME BPE, standards for Bio-Processing
Equipment. |
Material: T316L
Stainless Steel. Sulfur content of 0.005-0.017% |
Sizes: 0.5" -
4" OD tube sizes |
Tolerances: Tolerances
as specified in ASME BPE Part DT
Dimensions: Classic
lengths as specified in Waukesha Cherry-Burrell BPE Fitting Brochure,
and ASME BPE Part DT.
Finish: Combinations
of surface finishes are available to meet customers' requirements
(see below):
#7 |
|
|
|
|
Inside
diameter polish options:
|
|
Outside
diameter is mechanically polished with polish marks blended |
|
|
|
|
|
|
|
|
1Refer
to Table SF-4 of ASME BPE Part SF
Waukesha
Cherry-Burrell uses a multi-pass polishing method, utilizing
progressively finer grits to achieve desired finish.
NOTE: Some 0.5" and 0.75" elbows
require slurry finishing due to configuration. (Please
contact factory for more polish and electropolish information.)
Additional options are available. Contact factory for
options not shown. |
Pressure
Ratings: S-Line Clamped Unions
PSI
Service Rating
1Solid
Teflon2 and Teflon2 envelope gaskets
are not suited for use with this clamp.
*Not for use with 1.0" Fittings
Service
Ratings are based on hydrostatic tests using standard elastomer
gaskets, properly assembled joints, and no shock pressure.
Cleaning: |
Finished
parts are subject to a six-step RO water cleaning cycle. |
Etch: |
S-Clamp/BPE
Fittings are etched with heat number(s), WCB logo, material
grade, and SFF polish designation as specified in ASME
BPE Part DT (0.5" & 0.75" carry the first
three labels). |
Packaging: |
Fittings
are capped and either bagged or skin wrapped. |
Documentation: |
Material
test reports are available upon request. |
Elastomers: |
Buna-N,
EPDM, PTFE (Teflon2), FKM (Viton2),
Silicone |
Approvals: |
Canadian
Standards Association (contact factory for more information). |
2Viton
and Teflon are trademarks of the E.I. DuPont De Nemours Company
AWF/BPE
Fittings Specifications
 |
Description: Automatic
Weld Fittings (AWF) for Bio-Processing Equipment (BPE).
Fittings with extended tangents to be used with orbital
welders conforming to ASME BPE. |
Material: T304
and T316L Stainless Steel. |
Sizes: 0.5"-4" OD
tube sizes
Dimensions: Classic
lengths as specified in Waukesha Cherry-Burrell BPE Fittings
Brochure FH1831, and ASME BPE Part DT.
Finish: AWF/BPE
Fittings are available in a variety of finishes to meet customers'
requirements (see below):
|
|
|
|
|
|
Inside
diameter polish options:
|
|
Outside
diameter is scotch-brite finished and passivated |
|
|
|
|
|
|
|
|
|
|
|
|
|
Inside
diameter polish options:
|
|
Outside
diameter is mechanically polished with polish marks blended |
|
|
|
|
|
|
|
1Refer
to Table SF-4 of ASME BPE Part SF
Waukesha
Cherry-Burrell uses a multi-pass polishing method,
utilizing progressively finer grits to achieve desired
finish.
NOTE: Some 0.5" and 0.75" elbows
require slurry finishing due to configuration. (Please
contact factory for more polish and electro-polish
information.) |
Cleaning: |
Finished
parts are subject to a six-step RO water cleaning cycle. |
Etch: |
BPE
Fittings are etched with heat number(s), material, WCB
logo, and SFF polish designation as specified in ASME BPE
Part DT (0.5" & 0.75" sizes carry the first
three labels). |
Packaging: |
BPE
Fittings are capped and either bagged or skin-packed. |
Documentation: |
Material
test reports are available upon request. |
|
|
Back
to Fittings Main Menu |
Product
Literature:
|
|
